RO/DI & Remineralization

RO/DI & Minerals: Aquarium Salt vs Reef Salt vs GH+ Guide for Aquarium Keepers

Understand the exact ionic differences between freshwater aquarium salt (NaCl), synthetic marine reef salt, and freshwater GH+ remineralizers—including Ca:Mg ratios, conductivity conversion factors, osmotic regulation, and US/UK/EU dosing calculations.

Updated 2026-11-22 · 1973 words

Zebrafish swimming in an aquarium with air bubbles

Why "Salt" Is Not a Single Substance in Aquarium Chemistry

Few nomenclature habits cause as much preventable livestock loss as referring to freshwater aquarium salt, synthetic marine reef salt, and freshwater GH+ remineralizers under the generic umbrella of "aquarium salts." Chemically, these three products occupy entirely different domains of solution chemistry. They differ in their constituent cations and anions, their effect on general hardness (GH) and carbonate hardness (KH), their electrical conductivity (EC) to total dissolved solids (TDS) ratios, and their physiological impact on gill epithelia, osmoregulatory ATPase pumps, and plant nutrient uptake.

When an aquarist strips tap water down to near-zero dissolved solids using reverse osmosis and deionization (RO/DI), every ion remaining in the display tank must be intentionally engineered. Substituting sodium chloride (NaCl) for a divalent-cation GH+ salt starves soft-water shrimp of calcium and magnesium needed for ecdysis (molting). Conversely, attempting to remineralize a planted freshwater aquarium with synthetic reef salt floods the water column with sodium, chloride, and excessive carbonate alkalinity, locking out iron and precipitating phosphate while burning sensitive stem plants. Understanding the exact ionic architecture of each product prevents costly misapplications.

1. Freshwater Aquarium Salt (Sodium Chloride, NaCl)

Standard freshwater aquarium salt—sold in cartons or tubs as "aquarium salt" or "tonic salt"—is uniodized, evaporated sodium chloride (NaCl) free of yellow prussiate of soda (sodium ferrocyanide) and other anti-caking additives found in culinary table salt. In solution, it dissociates completely into monovalent sodium cations (Na+) and chloride anions (Cl-).

Crucially, NaCl contributes zero General Hardness (GH) and zero Carbonate Hardness (KH). GH measures exclusively divalent cations—primarily calcium (Ca2+) and magnesium (Mg2+)—while KH measures acid-neutralizing capacity dominated by bicarbonate (HCO3-) and carbonate (CO32-). Adding 100 ppm of NaCl raises TDS and electrical conductivity (by roughly 200 µS/cm on a 0.50 NaCl conversion factor), yet a titration test for dGH and dKH will read 0.

Physiological Role and Narrow Clinical Scope

Freshwater teleost fish maintain an internal blood plasma osmolality of roughly 280–310 mOsm/kg, far more concentrated than the surrounding freshwater (typically 2–20 mOsm/kg). Water constantly diffuses inward across the gill lamellae, while ions leak outward. Fish counteract this by excreting copious dilute urine and actively pumping Na+ and Cl- inward via chloride cells (ionocytes).

  • Nitrite Toxicity Mitigation: Chloride ions compete directly with nitrite (NO2-) for active uptake sites on gill chloride cells. Maintaining a chloride-to-nitrite mass ratio of at least 10:1 (often 30–50 mg/L Cl- during an emergency cycle spike) blocks methemoglobinemia ("brown blood disease").
  • Short-Term Osmotic Relief and Ectoparasite Baths: Raising ambient NaCl to 1–3 g/L (1,000–3,000 ppm) reduces the osmotic gradient across damaged skin or gills, conserving metabolic energy while dehydrating ciliated protozoa such as Ichthyophthirius multifiliis trophonts or Trichodina.
  • Why It Fails as a Routine Remineralizer: Long-term exposure to elevated NaCl in soft-water species (e.g., Paracheirodon tetras, Caridina shrimp, and Cryptocoryne) disrupts renal function, inhibits potassium (K+) uptake at root hairs, and leaves fish deficient in Ca2+ and Mg2+.

2. Synthetic Marine Reef Salt (Complete Seawater Matrix)

Synthetic reef salt is a multi-component inorganic blend engineered to replicate natural seawater (NSW) at a standard salinity of 35 practical salinity units (PSU, or parts per thousand, ppt), corresponding to a specific gravity of 1.0264 at 25 °C (77 °F). Unlike simple NaCl, reef salt contains all six major conservative seawater ions plus minor and trace elements buffered to a natural oceanic pH of 8.1–8.3.

In natural seawater at 35 ppt, sodium and chloride account for roughly 85.7% of total dissolved salts, while sulfate (SO42-), magnesium (Mg2+), calcium (Ca2+), potassium (K+), and bicarbonate (HCO3-) make up the remaining 14.3%. Reef-grade formulations elevate calcium (400–450 mg/L), magnesium (1,280–1,380 mg/L), and alkalinity (7.5–11.0 dKH) to support calcification in scleractinian corals (aragonite skeleton deposition) and coralline algae.

Brackish Water: Why Reef Salt Beats Freshwater Aquarium Salt

A common misconception in brackish-water keeping (for species such as Figure 8 puffers, Dichotomyctere ocellatus, or bumblebee gobies, Brachygobius xanthozonus) is that freshwater aquarium salt can be used to reach 1.005–1.012 specific gravity. In reality, estuarine water is diluted seawater, not concentrated NaCl brine. Mixing pure NaCl to 1.008 SG produces water devoid of buffering capacity, magnesium, and calcium, causing severe pH crashes and skeletal deformities. Always use synthetic marine or reef salt for brackish systems.

3. Freshwater GH+ and GH/KH+ Remineralizers

Freshwater remineralizers are formulated specifically to restore bioavailable divalent cations and, where desired, carbonate alkalinity to RO/DI water without introducing excess sodium or chloride. They split into two distinct sub-classes:

  • GH+ Only (Acidic / Soft-Water Profiles): Composed primarily of calcium sulfate (CaSO4), magnesium sulfate (MgSO4·7H2O), and sometimes small amounts of calcium chloride (CaCl2) and potassium sulfate (K2SO4) plus trace chelated micronutrients. GH+ adds 0 dKH, allowing active buffering aquasoils (e.g., humic-rich volcanic granules) to hold pH between 5.5 and 6.5 for Caridina cantonensis shrimp, discus, and soft-water biotopes.
  • GH/KH+ (Neutral / Alkaline Profiles): Combines the divalent Ca2+ and Mg2+ salts above with potassium bicarbonate (KHCO3) or sodium bicarbonate (NaHCO3) in a fixed ratio (commonly 1.0 dGH : 0.5 dKH for planted tanks, or 1.0 dGH : 0.7–1.0 dKH for Neocaridina and livebearers).

A hallmark of quality planted-tank and shrimp GH+ blends is a controlled calcium-to-magnesium mass ratio of 3:1 to 4:1 (which corresponds to an approximate 1.8:1 to 2.4:1 molar ratio, because calcium's atomic weight is 40.08 g/mol versus magnesium's 24.31 g/mol). Because both ions compete for uptake channels in aquatic plants and crustacean gills, skewed ratios (such as adding pure Epsom salt, MgSO4, without calcium) trigger antagonistic nutrient lockout.

Comparative Ionic Matrix

Parameter / Ion Aquarium Salt (NaCl) Synthetic Reef Salt (at 35 ppt) Freshwater GH+ (at 6 dGH) Freshwater GH/KH+ (at 6 dGH / 3 dKH)
Primary Cations Na+ (100% of cations) Na+ (~10,780 mg/L), Mg2+ (~1,290 mg/L), Ca2+ (~415 mg/L), K+ (~399 mg/L) Ca2+ (~30–34 mg/L), Mg2+ (~7–10 mg/L), minor K+ Ca2+ (~30–34 mg/L), Mg2+ (~7–10 mg/L), K+ / Na+ from KH salt
Primary Anions Cl- (100% of anions) Cl- (~19,350 mg/L), SO42- (~2,710 mg/L), HCO3-, Br- SO42- and/or Cl- SO42-, Cl-, HCO3-
Impact on GH 0 dGH (None) ~360+ dGH (Extreme; predominantly Mg2+) +6.0 dGH (107.1 mg/L as CaCO3) +6.0 dGH (107.1 mg/L as CaCO3)
Impact on KH 0 dKH (None) 7.5–11.5 dKH (Brand-dependent) 0 dKH (None) +3.0 dKH (53.6 mg/L as CaCO3)
Typical EC / TDS Factor 0.50 (NaCl standard) Measured in PSU / SG (53.0 mS/cm = 35 ppt) ~0.55–0.64 (meter-dependent; use µS/cm) ~0.60–0.66 (use µS/cm for precision)
Valid Application Short-term nitrite block & freshwater parasite dips Marine reefs, FOWLR, and brackish aquariums Caridina shrimp, soft-water biotopes, active-soil aquascapes Inert-substrate planted tanks, Neocaridina, community fish

Conductivity vs. TDS: Avoiding Meter Calibration Traps

When remineralizing RO/DI water, handheld TDS pens can mislead aquarists because TDS is not measured directly—it is calculated by multiplying measured electrical conductivity (EC, in µS/cm) by an internal conversion factor. Most inexpensive North American TDS pens are calibrated to a 0.50 NaCl factor, whereas some European and laboratory meters use 0.65 (442 natural water) or 0.70 (KCl). Because sulfate-rich GH+ salts conduct slightly less current per milligram than sodium chloride, a reading of "120 ppm" on a 0.50-factor pen corresponds to 240 µS/cm, whereas a 0.65-factor pen reading the exact same water will display "156 ppm." Always target raw electrical conductivity in µS/cm and verify final hardness with a liquid titration kit (1 dGH = 17.848 mg/L as CaCO3).

Worked Examples: US, UK, and EU Remineralization Scenarios

US Worked Example: 40-Gallon Breeder Crystal Red Shrimp (Caridina) Setup

A keeper in Seattle, Washington (soft municipal water, ~35 ppm TDS, but treated with chloramines) sets up a 40-US-gallon breeder tank (36 × 18 × 16 inches) with active buffering aquasoil. After accounting for 2.5 inches of substrate and driftwood, net water volume is 34 US gallons (128.7 L). The target profile for Caridina cantonensis is 5 dGH, 0 dKH, 130–145 µS/cm, pH 6.0–6.2 at 70 °F (21.1 °C).

  1. Product Selection: Pure GH+ mineralizer (0 KH). Aquarium salt is excluded (no Ca/Mg; toxic to shrimp osmoregulation at elevated NaCl). Reef salt is excluded (high KH exhausts active soil buffering within weeks).
  2. Batch Calculation: Using a standard powdered GH+ salt rated at 1.5 g per 10 L to achieve 6 dGH (200 µS/cm), the dose for 5 dGH is scaled linearly: 1.5 × (5 / 6) = 1.25 g per 10 L.
  3. Total Initial Dose: (128.7 L / 10 L) × 1.25 g = 16.09 g of GH+ powder dissolved in a 5-gallon RO/DI bucket, aerated for 20 minutes, and verified at 138 µS/cm and 5 dGH on a drop test before adding to the tank.
  4. Top-Off Rule: Evaporation removes pure H2O and leaves all Ca2+ and Mg2+ behind. Weekly evaporation top-offs use 0 TDS RO/DI water only—never remineralized water.

UK Worked Example: 180-Litre High-Tech Planted Tank with Soft Yorkshire Tap vs. RO/DI

An aquascaper in Sheffield, UK operates a 180 L rimless tank (net volume 155 L) with pressurized CO2 injected to 30 mg/L, inert quartz gravel, and demanding stem plants (Rotala macrandra, Tonina fluviatilis). Local supply is soft (~3.2 dGH, 1.8 dKH), but seasonal agricultural nitrate spikes reach 28 mg/L NO3-. The keeper switches to 100% RO/DI water at 24 °C targeting 6 dGH and 2.5 dKH (pH ~6.6 under 30 ppm CO2).

  • Product Selection: A balanced freshwater GH/KH+ remineralizer, or a DIY split using GH+ (CaSO4/MgSO4) plus potassium bicarbonate (KHCO3) to avoid adding sodium.
  • CO2 & KH Interaction: At 2.5 dKH and 30 mg/L dissolved CO2, the Henderson-Hasselbalch relationship holds pH near 6.45–6.55 without risking a biological pH crash. Using pure GH+ (0 dKH) in an inert gravel tank with 30 mg/L CO2 would drop pH below 5.2 and stall nitrifying bacteria.
  • Weekly 50% Water Change Dose: For a 77.5 L change using a GH/KH+ product dosed at 2.0 g per 10 L for 6 dGH / 3 dKH, the keeper weighs 15.5 g into a 80 L food-grade barrel, mixes with a 1,000 L/h powerhead for 30 minutes, and verifies 240 µS/cm before pumping into the display.

EU Worked Example: 240-Litre Brackish Figure 8 Puffer System (Berlin, Germany)

A hobbyist in Berlin, Germany—where municipal groundwater is very hard (16–20 °dH, ~650 µS/cm, high silicate)—keeps two Figure 8 puffers (Dichotomyctere ocellatus) in a 240 L aquarium (net 205 L) at 25 °C and a target specific gravity of 1.005 SG (approx. 7 ppt salinity).

  1. Why Tap Water + Aquarium Salt Fails: Adding freshwater NaCl to Berlin tap water pushes total dissolved solids arbitrarily high without matching marine ionic ratios, while tap silicates fuel persistent brown diatom blooms.
  2. RO/DI + Reef Salt Calculation: Standard synthetic reef salt requires ~38.2 g per litre to reach 35 ppt (1.0264 SG). To achieve 7 ppt (1.005 SG), the linear scaling factor is 7 / 35 = 0.20, yielding ~7.64 g of reef salt per litre of 0-TDS RO/DI water.
  3. Total Fill Dose: 205 L × 7.64 g/L = 1,566 g (1.57 kg) of synthetic reef salt. After 2 hours of vigorous circulation and heating to 25 °C, a calibrated optical refractometer (ATC) reads 1.005 SG (7 ppt) and KH tests at ~2.0–2.4 dKH—ideal for estuarine nitrifiers and puffer osmoregulation.

Target Chemistry Reference by Biotope

Livestock / System Type Salt / Mineral Class Target GH (dGH) Target KH (dKH) Target EC / SG
Caridina Shrimp (Bee / Taiwan Bee) Freshwater GH+ Only 4–6 dGH 0–1 dKH 110–160 µS/cm
High-Tech Planted (Inert Substrate, CO2) Freshwater GH/KH+ 5–7 dGH 2–3 dKH 180–260 µS/cm
Neocaridina & Livebearers (Guppies, Mollies) Freshwater GH/KH+ 7–10 dGH 3–6 dKH 280–420 µS/cm
Brackish Estuarine (Figure 8 Puffer, Mudskipper) Synthetic Marine / Reef Salt N/A (Marine Matrix) 2.0–4.5 dKH 1.005–1.012 SG (7–16 ppt)
SPS / LPS Marine Reef Synthetic Reef Salt N/A (Ca 420 / Mg 1320 ppm) 7.5–9.5 dKH 1.025–1.026 SG (35 ppt)

Diagnostic Checklist: Preventing Salt & Remineralizer Errors

  • Verify the Label Chemistry: Confirm whether the container states 100% sodium chloride (aquarium salt), multi-ion marine salt (reef salt), or Ca/Mg-based freshwater remineralizer (GH+ or GH/KH+). Never dose by "tablespoons per gallon" across different brands; always weigh in grams.
  • Cross-Check EC Against Titration Drops: Measure your mixed batch with an EC/TDS meter first, then confirm both dGH and dKH with liquid drop kits during the first three batches of any new salt bucket.
  • Pre-Dissolve Outside the Display: Never dump dry GH+ powder or reef salt directly onto livestock or plant leaves. Mix in a dedicated food-grade HDPE container with a circulation pump until crystal clear.
  • Respect Evaporation vs. Water Changes: Replace evaporated water exclusively with un-remineralized 0-TDS RO/DI water. Add salts and minerals only to new water replacing drained tank volume.
  • Match Temperature Before Transfer: Bring the remineralized batch within ±0.5 °C (±1 °F) of the display tank before pumping it in, especially in marine and shrimp systems where temperature alters specific gravity and conductivity readings.
Editorial & Safety Notice: This guide is provided for educational planning across US, UK, and European residential standards. Always verify ammonia, nitrite, KH/GH, and CO₂ levels with calibrated aquarium test kits and acclimate livestock gradually.

Reference Sources

  • Standard Methods for the Examination of Water and Wastewater: Hardness and Salinity
  • Seawater Ionic Composition and Synthetic Salt Formulations
  • Freshwater Fish Osmoregulation and Mineral Requirements